Login
You're viewing the pawb.fun public feed.
  • Nov 14, 2026, 10:22 AM

    microscope focus slide still isn't really moving. onto the 3d printer heat bed it goes. if that doesn't work I guess I'll soak it in brake cleaner or something…

    💬 1🔄 0⭐ 3

Replies

  • Nov 14, 2026, 10:26 AM

    *opens window so she doesn't pass out from WD40 fumes*

    💬 2🔄 0⭐ 6
  • Nov 14, 2026, 11:31 AM

    there is progress! I have removed another panel that was held on with some push-pins and got the ways to move far enough to reveal what looks to be two linear ball bearing cages sticking out between the outer and inner ways. which suddenly makes this a lot more annoying.
    they move at half the speed of the rest of the mechanism and their ends are bent over to lock them in place.

    photo of the inside of the microscope showing a pair of beefy slide ways with black metal shims sticking out between them. their ends are bent over into a T shape.
    💬 1🔄 0⭐ 5
  • Nov 14, 2026, 12:02 PM

    ok, looks like I can't get any further through there. time to take off the smaller slide for attachments that go under the table and see if there are more screws hidden under there.
    unfortunately the screw that acts as endstop on that dovetail is just spinning freely in it's hole and seems to be bent at the tip where it rides in a slot in the dovetail. cool…

    💬 1🔄 0⭐ 3
  • Nov 14, 2026, 12:58 PM

    fucking finally!

    photo of the microscope with the focusing slide removed from the upper arm
    closeup of the very beefy focusing slide. it's a big linear ball bearing
    💬 2🔄 1⭐ 7
  • Nov 14, 2026, 1:20 PM

    well poop, even after cleaning the linear bearing it's still incredibly stiff. so it looks like the problem is somewhere in the gearbox driving the rack and pinions :|

    💬 1🔄 0⭐ 1
  • Nov 14, 2026, 1:22 PM

    but holy moly, I'm in absolute awe of the size of this lad. this thing is built better than the cross slide on my lathe.

    Photo of the side of the focusing slide and fine feed gearbox. The slide is thick, with like, three Cs.
    💬 1🔄 0⭐ 6
  • Nov 14, 2026, 2:00 PM

    I'm starting to think the thing must have a focus lock that's stuck in place cause there are some end stops in one of the coarse focus knobs that look like they'd limit rotation of one knob relative to the other. unfortunately it's absolutely not budging

    💬 1🔄 0⭐ 2
  • Nov 14, 2026, 2:32 PM

    Aha! So it does have a brake on the focus. Unfortunately mine seems locked in place…

    4.3. Einstellen der Triebgängigkeit
4.3.1. Grobtrieb
Das Mikroskop ERGAVAL wird mit gelöster Triebbremse geliefert. Diese Maßnahme dient dem Schutz des Triebwerks vor Transportschäden. Um die Gängigkeit des Grobtriebs einzustellen, bewegt man den Trieb so weit, daß man keinen Anschlag fühlt. Dann umfaßt man beide Grobtriebknöpfe und verstellt sie gegeneinander so weit, daß die Gängigkeit den Anforderungen genügt.
    💬 0🔄 0⭐ 0
  • 💬 1🔄 0⭐ 1
  • 💬 0🔄 0⭐ 1
  • 💬 0🔄 0⭐ 1