Login
You're viewing the functional.cafe public feed.

Replies

  • Nov 11, 2026, 6:25 PM

    Out of the oven. Pics coming later but there's some graping on the joints probably because of more oxides on the type 5 paste. I kinda figured this might happen.

    Might try adding more flux when i mount the module to the carrier board in hopes of clearing it up.

    💬 3🔄 0⭐ 0
  • Nov 11, 2026, 6:55 PM

    OK time to grab some proboscis pics now, then put it on ice until I have time (tomorrow maybe) to make the carrier board to actually try it out

    💬 1🔄 0⭐ 0
  • Nov 11, 2026, 7:10 PM

    Solder paste on the board. Slightly overexposed I think but perhaps room to tweak the raw? You can clearly see the solder particles even in the type 5 paste

    Macro photo of board with solder paste on it. The back of the image is somewhat blurred.
    💬 1🔄 0⭐ 0
  • Nov 11, 2026, 7:12 PM

    Post reflow, definitely visible graping on some of the solder joints but I think it's probably going to work? I'll definitely add more flux all over the place when I reflow it to the carrier board and hopefully that will clean it up and give better results.

    This was my first time using T5 paste. I may have to look at N2 purging or something, or a higher activity flux?

    Nothing I see is giving me immediate "it won't work" red flags at least, I don't think there's any obvious shorts.

    Macro photo of WLCSPs on PCB showing shiny silicon
    A different angle of the board showing some incompletely coalesced solder joints
    💬 1🔄 0⭐ 0
  • Nov 11, 2026, 7:19 PM

    Low angle macro shots looking at WLCSP balls. For scale the STM32L431 is 0.35mm pitch, the FPGA is 0.4, most others are 0.4 or 0.5.

    The oscillator doesn't look great in terms of the solder actually coalescing. I might actually want to just add some flux and cook it before I put it on a carrier just to be sure.

    Angled view of STM32 balls looking mostly OK
    Angled view of FPGA balls lookign decent
    90 degree rotated view of same area
    Another rotated view
    💬 1🔄 0⭐ 0
  • Nov 11, 2026, 7:20 PM

    Not thrilled with the oscillator (the long skinny 4 ball BGA at left) either.

    Type 5 paste is definitely harder to work with than T4.

    Side view of the oscillator showing BGA balls sitting in incompletely coalesced solder
    💬 0🔄 0⭐ 0
  • Ben0h00000000@ioc.exchange
    Nov 11, 2026, 8:04 PM

    @azonenberg It might be worth ordering one of those cheap digital dental xray setups off alibaba to see what's going on under the BGAs.

    💬 0🔄 0⭐ 0
  • 💬 1🔄 0⭐ 0
  • Nov 11, 2026, 8:48 PM

    @tom_verbeure it's a little som with a trion t20 and stm32l431 serving a couple of purposes...

    1) try out jlc hdi on a low consequence project
    2) see how viable hand assembling ultra fine pitch stuff at home is
    3) do my first trion fpga design before i do some more complex real efinix projects
    4) maybe end up with a som i can use for future low power space constrained projects

    💬 1🔄 0⭐ 0
  • 💬 0🔄 0⭐ 0