Login
You're viewing the functional.cafe public feed.
  • Oct 8, 2026, 10:13 PM

    So I lasted until last night before making permanent modifications to my new 3D printer. And then I lasted until 30 minutes after that before killing the PSU cooling fan mosfet. Whoops.

    Turns out the fans I bought just don’t like PWM, they make a gurgling noise , which is rude.
    I put a big ol capacitor on there to try and smooth it and that went poorly.
    So I guess next I’ll remove the PSU board, replace that FET, and bodge a big ol LC filter on the output, which surely ought to do better?

    💬 1🔄 0⭐ 2

Replies

  • Oct 9, 2026, 1:39 PM

    Ok I tested a few versions and then soldered up one with a BS180 fet that then didn’t work (not low enough RDSon maybe??). Anyway so then drastic measures happened (throw FQP30N06L hammer at everything), and it lined up quite nicely around the side, and then I fit the inductor for the LC filter on there too. (Cap is by the connector, not shown.)
    So now it should have oodles of headroom to run 2 fans, and the LC filter seems like it’ll stop them buzzing without affecting the curve too badly.

    TO220 mosfet didn’t fit on the top of the Baird so it’s mounted to the bottom on VHB tape, with the legs bent around to the top
    The other side of the board showing the legs soldered to pads which happen to be in the right order right there
    The rear side again, now with an inductor on top of the FET and kapton tape insulating it all
    💬 0🔄 0⭐ 2
  • Oct 8, 2026, 10:47 PM

    @s0 bodge in a 4-wire cooling fan and find an extra I/o pin to drive its pwm input? No idea if there is anything that would physically fit and be workable with what voltage you have. MOSFET still useful because at least the ones I’ve played with can’t be stopped with just the pwm signal.

    💬 1🔄 0⭐ 0
  • Oct 8, 2026, 11:49 PM

    @acsawdey no spare IO pins on this daughter board unless I run wires back to main board, so I think I’ll try just replacing FET and filtering DC to the fan. I’d also like to avoid buying more different fans plus the 2 week wait for delivery.

    💬 0🔄 0⭐ 1
  • Oct 9, 2026, 2:12 AM

    @s0 Oof. Yeah slapping a bunch of LC on to make the PWM into the DC voltage of your choice seems like a good plan.

    💬 0🔄 0⭐ 0
  • 💬 1🔄 0⭐ 0
  • 💬 0🔄 0⭐ 0
  • 💬 1🔄 0⭐ 0
  • Oct 10, 2026, 4:51 AM

    @s0 unless you need something faster, lower R(d-s)(on), or lower V(g-s)(th), in which case there’s a few others from Diodes with the same pinout as the 2N7000. Trawling LCSC with a parametric search will show a few possibilities

    💬 1🔄 0⭐ 0
  • 💬 1🔄 0⭐ 0
  • Oct 10, 2026, 5:21 AM

    @s0 you may have better luck with TO-220 parts, TO-92 are starting to get pretty rare because switching parts are going SOT-23 and smaller surface-mount, and heavy-duty power-handling are going TO-220 and larger to handle the heat dissipation

    💬 1🔄 0⭐ 0
  • Oct 10, 2026, 11:43 AM

    @jpm yeah the TO-220 works fine, I just thought having something a bit smaller is useful. But probably should just go SOT-23 I guess

    💬 0🔄 0⭐ 0
  • Oct 10, 2026, 8:08 PM

    @s0 yeah it’s kinda interesting to go to LCSC’s MOSFET section, hey look there’s like 50,000 different parts! Filter by package TO-92, oh there’s only like 100. Filter by N-channel, oh only 50 now, and 40 of those are 2N7000 or BS170 from 20 different manufacturers.

    💬 0🔄 0⭐ 0