Login
You're viewing the functional.cafe public feed.
  • Sep 5, 2026, 10:08 AM

    btw, does anybody here on fedi have any experience with soldering bare #WS2812 / #SK6812 / #neopixels with a soldering iron?

    the packaging was pretty scary on expiration dates, saying that once the seal had been opened everything had to be used in 24 hours, or go through a baking process, because of moisture sensitivity.

    However, it also mentioned “reflow solder or other high temperature process”: does anybody know whether would it be safe to solder them with a soldering iron after some time in non-actively-dried storage?

    #electronics #SMD

    💬 3🔄 3⭐ 0

Replies

  • Sep 5, 2026, 10:12 AM

    qualcuno qui sul fediverso per caso ha esperienza nel saldare WS2812 / SK6812 / neopixels conn un saldatore?

    il pacchetto faceva abbastanza terrorismo sul fatto che una volta aperto il sigillo andavano usati tutti entro 24 ore o sottoposti ad un processo di asciugatura prima di usarli.

    Però parlava anche di “reflow solder or other high temperature process”: qualcuno sa se i problemi ci sono anche se li si salda col saldatore dopo che sono stati conservati in un ambiente non attivamente deumificato?

    💬 0🔄 1⭐ 0
  • Sep 5, 2026, 10:15 AM

    @valhalla first time I hear about that. Is humidity really that problematic at your place? I'd simply try it 🤷

    💬 0🔄 0⭐ 1
  • Sep 5, 2026, 11:09 AM

    @bekopharm I don't have condensation dropping down from the ceiling, but I don't have the < 10% humidity mentioned on the package either.

    At the moment I have used 10 LEDs out of a package of 20, and I'm going to try storing the 10 remaining ones and then try to solder them later, maybe at two different times.

    I'm a bit more hesitant to open the 50 LED package, however :)

    💬 1🔄 0⭐ 0
  • Sep 5, 2026, 11:30 AM

    @valhalla go for it! I doubt there is anything forming in such a short time surviving a real soldering iron 🤔

    💬 0🔄 0⭐ 0
  • Sep 5, 2026, 1:25 PM
    @bekopharm I believe that the problem is exactly the lack of survival of what has formed (moisture) under soldering temperatures, and what happens to it as it dies… er… suddenly evaporates
    💬 0🔄 0⭐ 0
  • Sep 5, 2026, 11:32 AM

    @valhalla keep them in an airtight bag with desiccant and they will be fine to hand-solder whenever you get to them in future.

    In short, yes MSL is definitely a thing, and good* vendors will pop a humidity indicator card into the pack so you know if they are ready to go as soon as you receive them or not. The issue is that many plastics are hydrophilic (they like to absorb moisture from the air), especially the plastics used in LEDs. When “wet” plastic is exposed to the 260°C ambient temperature of a reflow oven, the moisture can’t evaporate quickly enough so it turns to steam and builds pressure inside plastic packages which can make them explode.

    Hand-soldering is usually fine because you don’t heat the entire package, only the leads, and you should only need a couple of seconds of heating to solder the joint instead of a typical 5 minute reflow cycle

    💬 1🔄 0⭐ 0
  • Sep 5, 2026, 12:31 PM

    @jpm thanks! that's what was felt plausible, but also I was afraid to hope :)

    There was indeed an indicator card (and dessicant) in the bag, and the leftover LEDs have been put back into it, and closed with some tape, I guess put the bag into a zip bag with some extra dessicant just to be sure. I assume that the indicator bag will say that they have been exposed to humidity the next time I'll open the bag, but then I don't have a reflow oven (and I'll avoid using the hot air station just to be sure) :D

    💬 0🔄 0⭐ 0